A lot of very smart people have written in questions and suggestions and I think a lot of them are very clever and worth sharing... and I'd like to add some of my own expansions on what I showed in the video. Like they say, 2 brains are better than 1.... it turns out several thousand brains are even better. This post will be REGULARLY EDITTED to add new ideas as they come in. I know it breaks the RSS model, but I don't want to make a new post for every new idea. Sorry.
------------------------------------
My Bluetooth adapter and LEDs - Though it is reported to work with many bluetooth adapters and chipsets, I've been using this one sold by SparkFun electronics. The IR LEDs I use are Vishay TSAL6400s running at 100mA available from Mouser.
Tip switch - Instead of pressing the side button to illuminate the LED, a tip swtich could be added to illuminate when pressed on a surface. Though, it's mechanically harder to make and finding the right level of pressure for activation can be hard, especially if your surface varies (ex: whiteboard vs carpet)
Can you do this with a webcam? - The wii remote contains a 1024x768 camera with built-in hardware for IR blob tracking of upto 4 points at 100Hz. This significantly outperforms any $40 webcam I'm aware of. It'll work with a webcam, just not as well and not as easily.
Rear-Projection - using a rear projected surface, works great. The software will automatically work as-is so long as your pen is bright enough to shine through the projection surface. The wiimote gets a unobstructed view of the screen which eliminates occlusion problems and maximizes tracking resolution. Though, actually building a rear-projection wall or table can be a little difficult if you don't already have one.
Pressure sensitivity - wacom tablets give nice pressure sensitive behavior. Doing this with the wiimote whiteboard will be tough, at least through the camera data. The brightness of the LED varies significantly depending on angle, surface reflectivity, and distance. Any pressure data based off birghtness will not be reliable. The data could be transmitted via a high-frequency IR channel (like remote contol data) to an IR reciever mounted on the wiimote. (see "Right click" for more)
Right Click - any right click signal based off brightness is not likely going to be reliable. Additionally, using multiple LEDs (1 - left click, 2- right click) won't work at all distances and orientations as the LEDs get too close for the wiimote to distinguish them. The RIGHT way to do this is to use high-frequency IR data transmission (like remote control data) to an IR reciever. This will also give you a way of potentially getting pen ID - which is VERY powerful and may be a future project. Though, this requires quite a bit more hardware.
Multiple wiimotes for better tracking - if you have a large surface, you could have multiple wiimotes covering different areas to keep tracking reslution high, or have the wiimotes cover the same area to avoid occlusion problems, or do some interpolation of the data for higher accuracy. All possible, just with the smarter software. Doing this myself is probably not going to happen, but the source is freely available.
I have a nice 32 inch LCD do I actually have to touch the screen to make it work?
ReplyDelete@chase,
ReplyDeleteIf you want a touch screen then yes you do have to touch it (or you could just move the pen really close to the screen and just light up the IR LED). Basically you can map any surface to act as the area where you can manipulate your mouse cursor (think Wacom tablets).
As for using webcams, I think you would have to replace the IR filter in one with a normal light filter. This is how it's usually done with DIY multi-touch surfaces.
This comment has been removed by the author.
ReplyDeleteConcerning the right click, is it possible to do it using blinking flash
ReplyDeleteI wonder if you could configure you pen such that it flashed the ir light in a reliable manner depending on which button pressed (for right click or left click) and have the software translate flahses within a certain time frame as identification rather than more clicks
ReplyDeleteMaybe the IR LED should just move the cursor, and separate buttons on the pen would act as click button; of course this would require some mouse guts. Imagine if you used a laser instead of a LED; you'd get a pointer mouse instead of a touchscreen.
ReplyDeleteAlso, perhaps a well structured and moderated wiki would work better than updating a post when new ideas need to be added. The special category of recent changes in the wiki would easily allow people to see when new things are added.
Johny, where do you buy your ir leds? because i want to do this to
ReplyDeletethanks
P.S i really like your projects!
ReplyDeleteHello,
ReplyDeleteI was wondering if it is also possible to use an ir laser pointer instead of a ir LED pen. So you can manipulate your LCD screen from further away.
I really like the projects
Just some thoughts:
ReplyDeleteUsing two Wii Controllers you can have stereoscopic tracking in 3d space. Two eyes = depth of field.
On losing finger track:
To resynchronize finger tracking how about a resync motion - for instance bring all four fingers together as one point, first finger to go...
upper right = right index finger
lower right = right thumb
upper left = left index finger
lower left = left thumb
I'm with Ollie ... need more info on the IR LEDs.
ReplyDeleteWhat type of IR LEDs you use and which are best? Particularly confusing in the 'beam angle' talked about on product pages like this one: http://www.rentron.com/remote_control/IRLED.htm
For those who can make a have rear-projected surfaces (not me unfortunately) in a small or medium sized area I think the USB Finger Optical Mouse would also be an solution.
ReplyDeleteYou can find out more about it at http://www.uxcell.com/usb-finger-optical-mouse-for-notebook-laptop-p-6728.html
This with bluetooth instead of USB would be ideal of course.
Keep up with those great vids, loved them all.
About the right click -
ReplyDeleteWouldn't it be possible to modulate the IR signal quite easily? by using a small microcontroller and some switching it should be possible to implement almost any sequence into the IR pen. It would be quite nice to have, say, 2 buttons on the pen to send 'a modulated sequence blob' to the wiimote..
Best regards, Hans Peter,
Technical University of Denmark
Instead of using a pen, why not put a bit of reflector on you fingernail and use the IR emitter array from the multi-touch project. This gives you the mouse tracking, but you still need some way to do mouse clicks. Maybe by bending your finger so the reflector disappears?
ReplyDeleteHi
ReplyDeleteNice work, I'm looking forward to create an IR pen to try that myself :)
I'm interested in how this is working and looked at the code. The important part is the warp matrix construction done using the computeSquareToQuad and computeQuadToSquare functions, but I don't understand them. Can you do an explanation or give some references about that?
hi,is it ok to youse ordinary ledlights?
ReplyDeleteI tryed it today with my laptop and my wiimote. It is not acurate enough. Maybe because I was using an IR LED from a TV remote? And my swithch was a little wierd. I just didn't work as it shoud. I will go to electronic store and buy new LEDs and switch.What is the correct type for IR LEDs?
ReplyDeleteThis comment has been removed by the author.
ReplyDeleteI found this amazing, and had to try, mounted a ir pen, it worked but when I draw ie Paint the drawings are very noisy and squared, not round and soft like in the video, tried many angles and distances and cant solve, what I'm doing wrong? Can my wiimote bad? thanks. (PS: im using a CRT monitor)
ReplyDeleteExpo pens are PERFECT for wiipens. AA batteries slide right in and the IR LEDs also fit very well out of the tip, but need a little cushioning for snugness. However, the end of an Expo parker is hard to get off, but you can probably replace that with a different cap (cut top of plasstic bottle off, glue onto the end of marker and you're done).
ReplyDeleteThanks for the awesome use for my wiimote and bluetooth!
i figured out one of the reasons that the remote can have bad tracking sometimes. the wiimote is sensitive enough that it will actually pick up the light emitted directly from the led AND the light reflected off of the screen. i noticed that whenever the remote was very jumpy it was switching between seeing one and two points. i found that using a flat surface, in my case a wooden cabinet door just to test, the resolution was much better. i wonder if maybe diffusing the led with some sandpaper or something of that sort would improve tracking on a screen.
ReplyDeleteDespite my electrical ineptitude, I managed to hack an IR LED pen together today. I used an Avery Hi-liter pen (Expo dry-erase pens were more expensive), and everything else came from Radio Shack: 1.2v/100mA 45deg 5mm IR LED, mini momentary switch, N-sized battery holder, and N-size batteries (the AA battery holder doesn't fit and I don't have the skill yet to do this without ready-made holders). Drilled a hole towards the tip of the pen for the switch, glued the IR LED at the tip, threaded the wires into the pen and out the switch hole, soldered them together, and crammed them back in. It feels quite solid, though the button isn't great.
ReplyDeleteTested it on my 24" LCD monitor and it works, but all the lines are jaggy.
The battery's 1.5v, and I didn't get a 3.3 ohm resistor, so the LED is being overdriven, which may be creating too much reflection. Can't wait until work's off winter break so I can try it with our projectors.
I really want to try to get an active tip (push the LED in to activate it), but I'm not sure how to go about that.
Hello, your project is very interesting and I will try to make it in this holiday. By the way, can you post the picture of your a simple schematic of the light pen ? Since the link before its not work.
ReplyDeleteMerry Christmas!
The reported resolution of the Wii's PixArt camera is not necessarily the same as the resolution of the camera sensor itself.
ReplyDeleteThe update rate of the Wii Remote data is not necessarily the frame rate of the camera sensor.
TrackIR runs at 358x290 @ 120fps @ 40-50 degrees Celsius using USB power. I don't believe the Wii's PixArt camera sensor can run at 1024x768 @ 100Hz off 2 AA batteries at low heat.
PixArt cameras are typically 30fps.
As a PhD student I'm sure you can understand the importance of verifying technical specifications before publishing them!
This comment has been removed by the author.
ReplyDeleteHere's the Expo pen I made. The switch I used was a little too big so I had to cut a hole in the bottom to fit it all.
ReplyDeletehttp://i130.photobucket.com/albums/p253/
chrisluedtke/102_0129.jpg
http://i130.photobucket.com/albums/p253/
chrisluedtke/102_0135.jpg
Yes, those holes were made with my hot solder iron.
I haven't tested anything yet because it turns out my dongle isn't detected by Bluesoleil. You can go here http://www.wiili.org/forum/
bluesoleil-solution-for-not-supported-adapters-
t794.html if you want to help me out. I'd appreciate it.
Hi,
ReplyDeleteWe can imagine an other application of your idea in an other way : domotic !
Imagine a room with 4 walls equiped by wiimote. The person in the room wear a glove with IR transmiter on each finger. We can have a TV without any button, or a cooker without any button. A computer calcul the position 3D in the room an can turn on the TV because the finger simule the pression on a button. Sorry, i'm not clear because i'm not very good in english. I hope you understand what i mean.
Thank you for this.
ReplyDeleteI bought a $2 led keyring at Walmart and $2 infrared led at Radioshack, and in 90 seconds swapped leds and it works.
I finally got my Anycom bluetooth dongle to connect the Wiimote with a new stack following a wii wiki advice.
Now the wiiwhiteboard works for Cursor Control, but no whiteboard (drawing) capability. Am I missing something? Aren't we supposed to be able to draw on the screen when you uncheck Cursor Control?
Would it be a good idea to point with a red laser at the white screen, instead of painting with a led pen?
ReplyDeleteFisrt of all, Would it work?
I have tried red laser pointers and they don't work. I don't think the light is in the same spectrum as infrared, so the wii camera can't see it.
ReplyDeleteHi Johnny,
ReplyDeletehave you tested this system with anyone that usually experiences nausea when playing first person shooters? I'm thinking that this system might solve that problem...
What with the holidays and all, I haven't had a chance to try building a light-pen yet, but I see lots of comments from people having problems. I would advise holding the pen so that the LED is on the end away from the board. As long as your grip on the pen is consistent, the quad-to-square transform should be able to compensate. Also, if you are right-handed, place the camera to look over your right shoulder, as shown in this image.
ReplyDeleteIf this isn't enough, you can then put a sleeve over the LED, so it won't reflect off the whiteboard, but will still be visible from the Wiimote.
I am a teacher at a High School and when you figure out this whole wiimote whiteboard for the mac you will make all my dreams come true. :)
ReplyDeleteI just whipped up a quick tute for anyone wanting a simple design for an IR marker. http://users.bigpond.net.au/barsdell/irmarker/
ReplyDeleteI haven't actually tried this thing out yet, but shall tomorrow at my friend's place, where there be wiimotes :)
um, why not just use the ir pen like you would with a passive digitizer on tablet pc?
ReplyDeletedon't even have to worry about palm rejection?
no need for buttons
just hold the ir point long enough at one spot, say for like 2 seconds and the computer can pick that up as a right click.
same as a passive digitizer (touchscreen without the special pen)
=)
If you looking for cheap IR stuff.
ReplyDeleteCheck dealextreme.com
Take:
http://www.dealextreme.com/details.dx/sku.88
and replace the UV LED with this:
http://www.dealextreme.com/details.dx/sku.2399
The Site have more cool cheap stuff..
I ordert some Stuff and it took about 17 Days form HK to Germany.
Some SKU's of (maybe) interest:
3643, 2047, 4669, 1253, 1100, 2227, 1465, 9137, 4791
And here the ugliest Glasses i can find:
http://www.dealextreme.com/details.dx/sku.8589
And sorry for my Bad English.
This comment has been removed by the author.
ReplyDeleteI would like to have the tip switch in the Wiipen I made, but I have no clue what I need, how I need to add it, and Where to buy the part. Has anyone completed a pen with the pressure-sensitive LED that turns on when touching a hard surface and off when it is not?
ReplyDeleteThis comment has been removed by the author.
ReplyDeleteI would love to see this on your whiteboard. It would make for an awesome demonstration video...
ReplyDeleteCrayon Physics.
http://www.kloonigames.com/blog/games/crayon/
Couldn't you have some sort of code for right- and left-click, kind of like TV remote controls do for volume up vs volume down?
ReplyDeletewoul this laser ir pen work???
ReplyDeletehttp://www.thinklasers.com/infrared-laser-pointer-pen.html
Johnny i think u can use a web cam to recognize the position of eye to perform same function of ur Wiimote
ReplyDeleteto use a web cam, you would have to have a web cam that sees only IR, or mod a cam. Its easy to mod, just take it apart, remove the IR filter (that most have and is usually a greenish tint) and replace it with a filter that blocks all other light and lets IR in. An exposed piece of film works good and is cheap. Put the web cam back together and done.
ReplyDeletefull instructions with pics here
http://www.instructables.com/id/Infrared-IR-Webcam/
Note: I am not responsible for you breaking your web cam or anything else.
hello
ReplyDeletefor the Right click:
You can make a new calibration of the pen to compensate the drift of the distance.
With 3 diodes, you can even make a real mouse
Think you change your program to that effect?
sorry for my Bad English.
Hello!
ReplyDeleteI wondered long time where to get IR led, then i got it, from old remote control. It works fine with 1.5V AA battery, that needed only some wires.
That works fine with my PC, but my laptot keeps saying "the application failed to initialize properly (0xc0000135). Click on OK to terminate the application.
Is there any way to get that to work? Laptop is Hp 530 Notebook, and there is Windows XP professional with SP3.
wesko, I think maybe it's the .NET version you have. I tried to find where I read that, but I couldn't. Make sure you have .NET 2.0 installed.
ReplyDeleteTHX! Now it works fine, i can show this to my cousins too. :)
ReplyDeleteIs there so much traffic that :
http://www.cs.cmu.edu/~johnny/projects/wii/
works only rarely? or what is the problem..?
Aren't you better off having the tip of the pen as the button (quite a smooth one so as not to scratch the screen) and mount the ir led slightly above it. As long as the pen is held the same way round (with the led pointing at the wiimote) then it should track just fine. It may even track better seeing as the led will point towards the sensor rather than the screen (which also causes reflection problems).
ReplyDeleteOn second thoughts I'm wondering whether it's best to have two types of pen available. Maybe one like I described in my post above for simply prodding the screen, ie for use as a touch screen media player using media center. Most of the time you're simply prodding the screen so a button on the end would be good. But if you want to write on the screen or scroll then the standard design of pen is probably better, if the button was on the end it is more likely to scratch the screen as a reasonable amount of pressure would be needed to ensure the button stayed pressed in. If you didn't put enough pressure then the button would more than likely not be pressed all the time you were writing resulting in large gaps in your text!
ReplyDeleteAlso thinking you don't necessarily have to map the touch screen part to the display. ie you could have the projector (or tv) displaying the film somewhere in your lounge and you could have the wiimote pointing at a wall or the table for example. You could have the play/pause buttons mapped out on your wall and simply touch the wall with the pen to play/pause the film etc. Of course it's no real use but it'd be great to show off to your friends, no one would believe that you could control a film by touching one of your walls!
ReplyDeleteHi all!
ReplyDeleteJohnny, great job! I have only seen the video, but would love to test it out.
If you could really think how to create a right click - I understand this is not supported - then it would be even better. My guess would be to light up both tip and end of the pen for a click if the wiimote can register this (ofcourse not very far away).
For the pressure activated LED tip - just use simple coil spring under the LED tip and let it move inside the pen when pressed against surface... then the coil spring connects say negative current and you leave the other connection so that it connects the positive of a battery only when you push the led a bit inside... then when you realease pressure, the positive connection is lost and thus the LED turns off.. This is mechanical so only works on hard-enough surfaces that you can really press against, but there might be some extra sensitive approaches too..
K
The right click surely has a simple option, basically make it like a pda or a tablet. ie press (or light on) for one second = left click, press (light on) for 2 seconds = right click. the click would have to happen when the light goes off I guess, not sure how that would work with writing on the screen but it works like that ok on a pda or tablet so I guess it would be able to work in this situation, although I know very little about programming.
ReplyDeleteAs for the solution above about putting a spring mechanism in for the button on the end, I personally don't think that any of that is necessary, just switch the button and the led round, with the led mounted as near to the tip as possible. You'd have to make sure that the led faces the wiimote when using it though.
I built 2 of the IR pens out of Expo markers, and one of the pens makes very jagged lines while the other makes pretty smooth lines. Any ideas on why this is so?
ReplyDeleteI built 2 of the IR pens out of Expo markers, and one of the pens makes very jagged lines while the other makes pretty smooth lines. Any ideas on why this is so?
ReplyDelete^^^ Assuming that you're using the same wiimote for both then I would have to say that it's either:
1. The led (maybe doesn't shine so bright, faulty?)
2. The battery (maybe low or not providing enough power to the led?)
3. Something blocking the view (maybe the led isn't out as much as on the other pen so the wiimote can't see it so well?)
4. Something to do with the electronics (maybe the switch is wired badly?)
Unfortunately it'll probably mean replacing each part until you work out which one is playing up which basically means building another one!
Maybe use the finger tracking function to see what the wiimote is seeing? I assume the wiimote is seeing your first led better than the second. If that's the case then it could be any of the above.
Hope that helps.
Ben.
Pressure sensitive touch detection, like the Wacom, could be done by connecting your IR pen back to the Wiimote via the nunchuck port.
ReplyDeleteThis would have the benefit of also powering your IR pen from the Wiimote batteries.
This could be done by adding a cheap pressure sensor and a cheap PIC or AVR micro.
A pressure sensor fitted into the pen just behind the IR led in it's tip could give an analog pressure value that you feed into a PIC or AVR micro ADC input. Some simple C code would then encode this value into the I2C message that the Wiimote understands, and sends this via a wired connection into the Wiimote nunchuck expansion port.
See the Wii Linux Wiki for details on the Wiimote I2C comms protocol.
http://www.wiili.org
Excellent set of projects JCLee, an inspiration to us all, keep up the good work!
And definately concentrate on the augmented reality projects. This is the real technology of the next gen consoles, peeps are finally starting to realise that more horsepower and sharper graphics just doesn't cut the mustard any more!
DeeDub
^^^ A massive wire would be needed and some sort of fixing to make sure a slight tug on the wire wouldn't move the wiimote as even a slight movement would make the screen out of sync. Other than that a very good idea.
ReplyDeleteA cable can be your friend too!
ReplyDeleteBut you're right, a big part of the Wii concept is wireless.
You could use bluetooth in the IR pen instead, and there's already talk of N1ntend0 releasing a wireless nunchuk.
So there could soon be an even simpler solution..
junk the AVR/PIC micro idea and just hijack one of the analog accelerometer inputs of a wireless nunchuk to monitor the IR pen pressure.
Wireless nunchuk?
http://www.verdicts.co.uk/computer_
games/articles/article-84.html
DeeDub
First off, let me just say that I think you have really done something great here! I can see this could go very far.
ReplyDeleteOne thing though...
Why do you not just start up a support or dev forums instead doing everything on the blog?
I think it would help, I can host it and even set the whole thing up...
just a suggestion.
I finally got to do some testing (aka, playing) with the projectors at work.
ReplyDeleteIt works pretty well at 'long range', with the Wiimote set well back from the screen (10+ feet wasn't a problem). At close range, the Wiimote may pick up two IR sources from one pen: the LED itself and the IR spotlight, which contributes to jaggies. When you're using it in an actual whiteboard setup, the Wiimote will only see the spotlight.
I want to get a wide-angle IR LED (the ones I bought were 60 degrees, I think) to see how I can play with mid-air shadow-based pointing, which could be useful for large projections (although that will only work if the Wiimote is right on top of the projector).
I've also given thought to the way the Wiimote Whiteboard software works and how it could be changed to increase functionality.
One of the problems is that it treats the momentary LED as a mouse click. You cannot do any 'mouseover' stuff without clicking on it. Instead of trying to make the pen increasingly complicated by adding in rapid flashers or something, can't the software be modified to use the IR blobs better? Detect one blob: mouse cursor, no click. Detect two blobs, the whiteboard software recognizes this as a left click at current position. Detect 3 blobs, software sends a right click. 4 blobs, a both-button/middle button click/scrollmode, whatever. It would require the software to recognize which blob is the 'cursor' blob so it doesn't get confused when more blobs are added, moved, and removed.
Of course, this does increase pen complexity by adding switches and LEDs, but I think it'd be easier than adding flash pattern hardware. Though, now that I've done this stream-of-consciousness pontificating, I'm not quite sure how to design the pen to properly accomodate all of these extra IR sources, at least if you want to make it as orientation-free as the original design.
I suppose I can try and find a cheap bluetooth presenter mouse and try to hack it and the IR pen together...
^^^ That's the answer.
ReplyDeletehttp://img248.imageshack.us/img248/1833/wirelesstrackballlv7.jpg
Buy one of these ^ for about £25 (think that's $50) and mount the led at the front and the battery near the bottom and have a switch in between. Simply turn the led on when using it and turn it off when finished. The program just needs to be changed to use the led as the cursor rather than a click. Now you have full cursor control (useful for hover over and making sure you're in exactly the right place before you click etc) and you have the left click on the trigger of the above product and scroll and right click on the top. This means no clicking needs to be programmed into the device, it's already there!
So you can get up close and write on the screen by holding the trigger down.
And you can use it from far away rather than having to stand infront of the screen and clock people from seeing.
ie if you want to get up and point at something or write/draw on the screen you can. If you want people to be able to see and just want to do usual things like scroll windows etc you can do it from wherever you want in the room.
All from one device!!!
Changing the led to cursor control rather than clicks also has the added advantage of meaning you can easily change the wiimote to point at anything to be able to draw. The problem with drawing on something that wasn't the screen before was that you couldn't tell where the cursor was before you clicked by which time it's too late as you've started drawing. This way you could turn a table for example into a massive graphics tablet being displayed on a big screen as you'd have cursor control to be able to see where you're about to draw.
Picture doesn't appear to work, piece these two bits together:
ReplyDeletehttp://img248.imageshack.us/img248/1833/wireless
trackballlv7.jpg
Wireless Trackball
ReplyDeletehere is a working link from benjimoron's comment
Is anyone having probelms with Office 2007 Apps? For example, in powerpoint i select the feltpen option. When i use the IR pen, i can make dots on the screen when i first turn on the IR LED (click the button). Then the "dot" is tracked around the screen along with the pen. This tells me that the IR LED is on and is being tracked. The issue is that no line is being drawn on the screen. I can use all other programs without any issues such as MS paint. Any Ideas?
ReplyDeleteFor right/left click, what about replacing the pointing laser with an IR diode in something like this:
ReplyDeletehttp://store.greenpearle.com/infiniterlr1.html
^^ Basically the same thing as I've posted above. That one looks to connect to the pc via infrared rather than 2.4ghz wireless so would require line of sight.
ReplyDeleteIt's probably a little nicer to hold in your hand but lacks a trackball so you couldn't use it from afar too and the buttons look like they'd need remapping as they're for page up/down etc. I guess that shouldn't be a problem but a little more work.
I think the one I posted is probably a little easier to hold the button down for a long period. The button on the pen would have to be held using the tip of your finger whereas the trigger on my one would be held by squeezing your hand. Easier for long periods IMO.
Yes, your changes would be necessary, and I think the "pen" format is easier than the "pistol grip" for me, at least.
ReplyDeleteI was thinking of placing a sleeve over the pen and sliding it over the laser button when I wanted it on. The buttons should work up to about 65ft., but I am not sure how coherent the IR laser (pointer relpacement) would be.
There are also laser pointers with RF for the buttons.
I really don't understand the trackball.
john: have you tested this project with the pen that you've mentioned?
ReplyDeletei'm wondering to buy one but it costs $57,00 here in Brazil. so i'd like to be sure first.
thx
Some people will prefer the pen, some will prefer the pistol.
ReplyDeleteNot sure how this sleeve would work? I assume it's got to be tight enough to keep the button pressed? Might be easier just to add a switch rather than keep a sleeve tight on a button? IMO holding the button to left click whilst writing for long periods is going to hurt your hand more than my method. But of course that's down to perosnal choice.
An RF version would be better.
The trackball (I assume you know what a trackball is, sort of like an upside down mouse ball. Basically provides the mouse movement function). The advantage of this is that you can use the device from anywhere in the room. ie with your pen you'd need to be right at the screen to do anything whereas with mine you would be at the screen to write/draw but you could do lots of things from wherever, it sitting down or the other side of the room so as to not block the view of the screen.
marco, the pen that john speaks about should work fine. But it relies on the laser being replaced with an ir led and the rest of the pen working with it. The voltage may be too high/low and the sleeve might not be easy to make.
ReplyDeletePersonally whichever solution you go with, the bits should simply be added on top. That way you don't rely on the rest of the electronics working with it. All you should need to add to the device is a battery, switch and the ir led. You may need a resistor, I'm not sure.
marco,
ReplyDeleteNo. I just read benjimoron's comments and found the pointer -- all today. I have used a sleeve on an regular pen-shaped laser pointer to keep the button pressed. I used a few mm of plastic tubing (just bigger in inside diameter than the diameter of the pointer).
The mod is similar to the ones proposed before, so it "should work". If I can find an affordable RF pen-shaped pointer (best I have found is USD55), I'll try that.
benjimoron,
My goal is to have the presenter in front of the screen. Now I see why you want the trackball -- it is probably good for your use. I already use something else to allow remote screen drawing.
Piece those together, if wynn could do the honours that would be fantastic.
ReplyDeletehttp://img144.imageshack.us/img144/4082/
trackballal1.jpg
That's basically the same thing but people may prefer it to the pistol version. The left click on this one is controlled by pressing the left button with your thumb. Bit more natural to write with I think but the left click and the trackball are both operated by the thumb rather than thumb and forefinger (I think that's the one next to the thumb!) in the pistol version. Makes clicking and dragging when not at the screen difficult.
John,
ReplyDeleteMy aim is the same as yours, to have the device right up at the screen to effectively make a touch screen. But at the same time to add left and right click, hence why using a wireless trackball. The advantage of which is that you can use it at the screen and also from a distance. 2 birds, 1 stone!
ya'll need to look at some html code! :P
ReplyDeleteTrack Ball
Go here to learn html link code
a quick suggestion: if you dont have an IR light pen. You can test out the system with a lighter.
ReplyDeleteand if you want to click while the lighter is on, just wave your hand in between the wii remote and projected screen once.
its definitely not as accurate, you can see the trail of flicker when using programs such as paint.
the nintendo wii, is much better at detecting IR blogs than a standard webcam. I've made a multitouch based from nuigroup.com, and using a webcam is very processor heavy.
ok, next idea!
ReplyDeleteThis requires a bit of extra co-ordination so I'm not sure that it'd be that great but I thought I'd throw it into the mixing pot anyway.
You could have the pen in your right hand, led permenantly on and acting as the mouse cursor. And in your left hand have a wireless trackball which is controlling the clicks.
Like I said this requires a bit more co-ordination and would take a while to get used to. But it does mean you can use a very simple pen for controlling the cursor and allows you to left/right click too.
I'm blown away!
ReplyDeleteHow hard would it be to adapt this to just a simple Home Theater PC remote control, using pointing?
Your demo shows you moving menus and windows around... why not HTPC applications?
Is it possible to 'click' using tap, like on a laptop trackpad?
I can envision a system whereby one merely gestures in the air toward their HTPC across the room and can select content, open and close applications, schedule recordings, fast-forward, rewind, etc.
You are definitely thinking out of the box with this project!!
Amazing!!!!
ReplyDelete:O
You have tapped into something that is very practical and useful in everyday life...
As Harry M commented earlier on, I too am interested in seeing if this will work with LinuxMCE
I'm looking forward to trying out these proj's @ home
especially the ir pen
=)
w00t!!!
Thank you for sharing and makin' these vids...
Can't wait to try out!!!!
Looking forward to more projects!!!
~ray v.
Harry,
ReplyDeleteIt is possible to click using a tap, read my comments above.
Gesturing in the air is nothing new, you can do it with the wiimote on its own rather than using leds or you could just buy a gyration mouse. These have been around for years and basically do the same thing. Look at software like streetdock if you want good gesture control. Only problem with waving in the air is you need to know where in the air the screen is aligned to in order to make good use of it.
Hey, This is some pretty neat stuff! in not actually having a wii i had no idea this was going on until someone sent me the Gizmodo link.
ReplyDeleteI got to playing with you whiteboard app and was unimpressed when i had to install some other application (bluesoliel) to use it so i got to tinkering around with brian peeks library on coding4fun.net and found your connect methods are mostly the same with the exception of the "if (!IsRemoteConnected((int)index))" part. once i changed your project to have the same connect as the 10.22.2007 wii-lib release, it works now with my linksys BT device and vista drivers! you just have to pair them. Just letting you know. Thanks for all the awesome projects! and keep up the good work! your stuff is amazing and my office loves the new electronic whiteboard, heh.
Congratulations on these great little brain teasers.
ReplyDeleteI've had some problems with cheaper IR leds (only 20mA), which did not have the juice to get detected, unless they were pointed at the wiimote... kind of defeats the purpose, just be aware and buy some powerful leds instead.
I've noticed someone challenging the 100Hz sampling rate and the resolution. It would be nice to have some confirmation, that these are indeed correct.
If they are, then I suspect we could build a device that would allow for 5 different programmable functions to be recognized - with relative safety - by the software.
Suppose:
F1: Led on.
F2: Led flashed at 20Hz.
F3: Led flashes at 40Hz.
F4: Led flashed at 60Hz.
F5: Led flashed at 80Hz.
These are sufficiently spaced apart, for software to be able to distinguish between them, after calibration (pen would need to be in sync). It could allow different actors to be differentiated in multi-user scenarios, or the "pen" could perform different actions: Left Click, Right Click, Paint, Erase, Brush, etc...
One more question: Why on earth does the wiimote track 4 blobs? Any ideas? It seems completely a waste, since the "sensor bar" has only two blobs on it...
I found a perfect ir pen at Walgreen today. An "LED Pen Light / With Pocket Clip", item #561434, from East West Distributing Co., in Deerfield, IL 60015.
ReplyDeleteIt's a standard pen-shaped pocket flashlight job with 2 AA batteries in the case, an on-off switch on top, and a white LED poking out the bottom, but the chip the LED's soldered to sits loosely in the case. I broke apart an old keyboard, cut out the thick centers of two of the rubber nipples used to make the keys pop back up, cut a small hole in the center of each, and inserted them between the end of the battery and the chip. It provides just enough resistance to break the circuit unless you press on the LED.
The pen itself was $5 and is stainless steel; actually quite a nice pen for the price. The rest was just junk, of course, and free. I'm able to vary the pressure at which the point reacts by trimming the height of one of the nipples. I'm certain you all could make much more elegant solutions, but it works very well, took a lot less work than diying the whole thing, and looks really good. Might keep an eye out for the flashlight.
Can I use multiple wiimotes to track more than 4 pens?
ReplyDeleteWould anyone like to use my website for discussion about these projects? I am not doing it for ads or site traffic, I just want to help the users here communicate with each other as best they can, and give them a great platform to do it.
ReplyDeleteWiimote Project
I just started the site so feel free to use it if you want.
Just had a thought about my idea to use multiple IR blobs to differentiate clicks.
ReplyDeleteClicks, unlike the cursor, don't necessarily need to be IN the IR pen.
Simply hook up what amounts to a Wii sensor bar to the back of your pen. Put the bar somewhere stationary by your screen, but out of the calibrated screen area. Run a power wire out to the sensor bar hooked up to extra switches in your pen. Push the extra buttons on the pen, and the sensor bar lights up.
Much simpler than trying to cram more lights or more sophisticated stuff into an Expo pen or cheap LED flashlight.
Now...anyone have any ideas for powering a Wiimote directly from USB power?
@eric
ReplyDeletehttp://www.coolest-gadgets.com/20070206/wiimote-usb-charger/
I know about those, but they're not what I have in mind. Those are chargers with a replacement battery pack.
ReplyDeleteI'm talking about something that lets me wire the wiimote directly into a USB cable, without a $20 possibly-defective (Nyko's charging station has been causing fires) charging unit between it.
Some Sony cameras at work came with wall adapters that were basically paired-AA-shaped shells with the contacts that had a wire going out to an external power brick that attached to the wall. That's what I want, but USB.
I considered getting some of those charging units to steal their battery shell and door, but I didn't want to spend $10 on the off chance I could do something with it.
If USB can't supply the required amperage (it tops out at 100mA, 500mA with some sort of negotiated handshake), some other connector would work. Just something that goes from batteries to external wires.
doesnt the guitar hero controllers have rechargeable battery packs? maybe one could wire one of those up, i dont know if they plug into the wall or a usb but its a thought
ReplyDeleteThis comment has been removed by the author.
ReplyDeleteJarrod,
ReplyDeleteLooks like that could be the bit of software to do it, I've posted before about changing it so that a 1 sec click is left and a 2 sec click is right just like a pda or tablet works. Not sure how that would work with drawing, would it realise that you wanted to hold the left down for drawing rather than thinking you were right clicking? A pda or tablet tells the difference by whether you're moving the cursor, ie if you're moving then you're drawing but if you're still then you're right clicking. Not sure if the software can handle that but it's certainly one of the solutions.
Only problem with it is that you don't get a cursor, you just get touch screen. Not a massive issue but a cursor is very handy sometimes.
On the subject of right clicking, I think someone mentioned a little earlier about lighting up more leds to mean different clicks. This could be a very good idea if the wiimote doesn't get confused as to which one is the cursor.
Suppose you had the main led on the tip of the pen permenantly on (with a switch to turn it off when not in use) and the wiimote tracks that as the cursor. You then have two more leds somewhere, doesn't have to be on the pen but probably easier to. Now you have two buttons on the pen, one for left and one for right click. If you click the left button then one of the leds light up, there are now two leds lit, one is the cursor, the other is for a left click. The wiimote should now report two leds on, this should work as long as the wiimote doesn't get confused as to which one's which. I think the wiimote recognises which one is which doesn't it as in the video with the blue and green pens and the swirly pattern on the table. The location of the second led is irrelevant, all the software would need to know is that there are now two co-ordinates being reported so that means left click. Same with the right click, 3 leds would now be lit (they need to be fairly seperate so they don't collide) therefore that means right click.
Anyway, where are you Johnny???
tabgab,
ReplyDeleteMust admit that I don't fully understand your question but I have a funny feeling that the wiimote is going to get confused by the pulsing lights, for example 20hz is repeated in 40,60 and 80hz and 40 is repeated in 80hz too so I guess at 80 they could all be flashing and I'm not too sure how it would tell the difference then anyway? Can't it tell the difference anyway as in the example I gave above, ie the video with the blue and green pen on the desk with swirly patterns?
I assume the wiimote tracks 4 as that was cheaper than making one that only tracked two. ie the manufacturer probably already made loads of units that tracked 4 therefore they work out cheaper.
Hi Johnny,
ReplyDeleteHave you considered putting a fish eye lens in front of the wiimote to obtain a much broader angle than the 45 degrees it has at the moment?
This comment has been removed by the author.
ReplyDeleteHi all,
ReplyDeleteWhere I am no Wiiremote in the market lol, I must use Webcame, Can you explain me how to use it ?
Best Regards.
Hey team
ReplyDeleteJust tried this software I posted with my in progress whiteboard, and it works fine for a actual MOUSE - but not for the wiimote! You can move the pointer and so forth, but holding down a 'eleft click' doesnt do anything, yet the mouse does.
I think its the software, knowing to look for a HUD mouse, while the wiimote is classed as a gaming device! Damn!
So, any ideas?
bejimoron,
ReplyDeleteI think you may have a valid point about possibly confusing different cycles, but that's a software problem. The wiimote would not have to interpret that. It would just give you blinking "blobs" at specific co-ordinates. You can then handle those from your code. Even the slowest of blinks can probably be profiled in about a quarter of a second, (5 flashes in .25sec means 20Hz, 10 means 40... the problem is, if the wiimote loses sight of the pointer for a short while, and then the software needs to figure out, just what's happening. If you cut down the number of functions to 4, then you will have more separation between the blinks, thus safer operation. We never know if it works, until someone tries it :)
One more question pls: I have now built two pens, each with a single 20mA 850nm led, but I am having trouble getting the wiimote to notice it. I am probably using the wrong led, with too little power, or too narrow a viewing cone. Any suggestions on which type work best?
@tabGab
ReplyDeletei got mine from radioshack. they are the only IR leds they have that i found and they are 100ma.
alternatively, i have a mostly see through pen that i used to make my pointer, and the pen has a moslty see through but still fogged up cap. when i put that on my led, it shows up way better. try and find something like that, or just something that will light up with the IR light so the wiimote can see it when it is not directly aimed at it.
Well, the answer seems to be in the 100mA leds. Mine were all 20mA, and that's way less. I'll just have to keep searching, since Radioshack is non-existent where I am.
ReplyDeleteFirst off, this is by far one of the coolest thing I've seen to do with the wiimote! This and the head tracking are fantastic!
ReplyDeleteRegarding the Right Click problem: why not sync a second wiimote that is configured with macros, held in your other hand? For example, hold down the trigger to simulate the right click function, (a la the Ctrl click on macs) press the 1 button to toggle the on screen keyboard, the arrow keys switch between pen colors, etc.
This would eliminate the hassle of trying to configure the whiteboard program to recognize different LED frequencies, which may be troublesome given the multitude of whiteboard setups. It also adds a lot more functionality to the whiteboard.
Of course, I don't have the programing knowledge to pull this off, but this is merely a suggestion. I'm pretty sure you could use GlovePie or something to create this control scheme. Let me know what you think.
WiimoteProject.com Is now up and running.
ReplyDeleteI have talked with Johnny and We are going to make it the official support forums for his Wiimote Projects. Please register there and start sharing your wisdom :)
If anyone would like to help with the site please PM dice on the new site. (thats me ;) )
as soon as i saw this i wanted to make it, and one link leads to another... I found some things of interest.
ReplyDeletehttp://www.whitenoiseaudio.com/touchlib/
http://wearables.unisa.edu.au/mpx/?q=mpx
thats for us linux users. The first link is Touchlib, which seems to be a library that supports tracking "blobs" of infrared as an input device. The second link is Multi-Point X Server (MPX), which allows you to use multiple input devices. It is pretty awesome what you can do with this. What if we combined the two? :D
http://www.instructables.com/id/Interactive-Multitouch-Display/
this looks like it may be combinable with your wii-mote obsession. Although Im not sure if I understand how this one works. Does the camera record infrared reflected off of your finger, or does the camera detect your finger by seeing where it blocks the infrared? What exactly does the acrylic do to the leds around the edges?
I found the answer to my question. This link helps explain how the instructables project i linked to in my previous post works. fascinating!
ReplyDeleteGreat work - I can't wait to see more.
ReplyDeleteA thought occured to me about multi-object tracking and labeling. First, on labeling, I have an ugly hack to differentiate between multiple IR sources - you could shield them with polarizers, and polarize multiple wiimotes. So, the vertical polarized wiimote sees light only from the vertival polarized IR, and the horizontal only from the horizontal. They both see the unpolarized one. So, with two wiimotes, you can uniquely identify three light sources, as long as they maintain their relative rotations.
Second, I'm envisioning a table workspace with tactile objects you want to track - chess pieces, for instance. Instead of a constant IR light, put a pulsing IR light that turns on and off in a recognizable pattern. It might not work great, but there's my thought. As long as only four of the pieces are on at any given moment, the wiimote can track all of their lights, and some other software can track their overall positions and their bit codes, and decode their unique ID. The problem here is synchronizing the lights to all turn on and off in the proper sequence. I imagine either radio control, or them all watching a clocked IR light near the wiimote to synchronize them.
Just a couple thoughts. Hopefully they're useful to someone.
I was wondering if anyone had the same problem as I did :
ReplyDeleteI first bought some IR Leds rated at 840nm. Performance was pretty terrible, at first I thought it was the angle that was to narrow. I then bought some 940nm leds that seemed less powerful when checking with a webcam, however, they work much better with the wii remote. Could it be that the wii remote doesn't work with IR Leds that are below 940nm ?
Chase: It has been my experience that you don't necessarily have to touch the screen to make it work. But the further you get back from the surface, the more awkward it gets to use. You also lose some ability to tell where the pointer is going to go. Your best bet would probably be to discipline yourself enough to not press on the screen too hard.
ReplyDeletehi:
ReplyDeleteI saw your demo "Low-Cost Multi-point Interactive Whiteboards Using the Wiimote" and I was wondering on 2:51 what software is that? It seems many stars suddenly appear when you press the screen. Is that kind of interactive software? Thanks
Awesome the applications you devised from the wii remote.
ReplyDeleteIm particularly interested in the video where you demonstrated calibration of two projector side by side.
I have a project of creating a small cinema room in the small town where my father lives but the cost of a projector that will five me a decent size/quality image is way too high for my pocket.
Your experiment shows that it might be possible to calibrate maybe 4 projectors together and get a decent size/quality image that might allow for the creation of a small size projection room where I might be able to fit about 50 people.
Is there any more info published by you on this project?
Do the images look seamless when the projectors run together side by side?
Thanks in advance and congratulations on your projects
Eder Wainer
eder@coll.com.br
We can do the same thing with only glovepie scripts?
ReplyDeleteyes i do it
ReplyDeletebut I am unable to convert the coordinates of the wiimote
help me please
Excuse me for my bad English
I am French
This comment has been removed by the author.
ReplyDeleteis there an IR camera that I could use in stead of the wiimote? I am trying to make a more permanent white board and dont want to have to change batteries or power on the wiimote, just a camera that is connected via usb to my computer.
ReplyDeleteCPT Matt,
ReplyDeleteI'm thinking the same thing, and here's what I've come up with so far:
For pairing the wiimote, I have a rubber band holding a plastic block over buttons 1 and 2. I can leave it there all day and all night.
For the batteries, I am going to feed a 3V power supply to it constantly. That way I'll never have to deal with it at all.
This comment has been removed by the author.
ReplyDeleteOne way to eliminate having to hold the side switch, is have an on/off switch (not momentary) that activate an electronic circuit. LEDs can also be used to sense light, so a circuit can be built to switch between photosensing and light emitting modes using a small microcontroller. When the circuit is on, and the pen tip is not near a surface, it intermittently outputs a pulse of light, switches into sensing mode to check the amount of reflected light and then goes idle for a period. When the pen is brought near a surface, the amount of reflected light during the sense phase changes, so the micro switches into operating mode. In this mode, it is mostly emitting light, and periodically switching into sense mode just long enough to check if it is time to switch back into its idle mode.
ReplyDeletecan somebody tell where i can find a infrared LED and tell if its infrared
ReplyDeletecan anyone tell me where to get an infrared at home and how to tell it is one
ReplyDeleteI worked the code a bit and added a right click at 1 second. (like a PDA) For some bizzare reason, it works perfectly everywhere except MS Excel. I think there must be some kind of extra activity that happens on right click in Windows whenever Excel is the active app.
ReplyDeleteI'll post a link later.
this was an issue in powerpoint as well. the resolution is below
ReplyDeleteChange the code in this way.
Line 68-71 of Form1.cs:
long
->
uint
Line 192 of Form1.cs:
SetCursorPos((int)warpedX, (int)warpedY);
->
mouse_event(MOUSEEVENTF_ABSOLUTE | MOUSEEVENTF_MOVE, (uint)(warpedX * 65535 / screenWidth), (uint)(warpedY * 65535 / screenHeight), 0, 0);
http://www.wiimoteproject.com
This comment has been removed by the author.
ReplyDeleteThis comment has been removed by the author.
ReplyDeleteJohn:
ReplyDeleteplease can any one HELP me!!
I downloaded the C# source code from this board, and when I attempt to run the program in debug mode I get this error:
A call to PInvoke function 'WiimoteWhiteboard!WiimoteWhiteboard.Form1::mouse_event' has unbalanced the stack. This is likely because the managed PInvoke signature does not match the unmanaged target signature. Check that the calling convention and parameters of the PInvoke signature match the target unmanaged signature.
on this line:
mouse_event(MOUSEEVENTF_LEFTDOWN, 0, 0, 0, 0);
the first time I attempt to click with the ir pen when calibrating.
and if I uncheck the cursor option, and try it I get:
cross-thread operation not valid: Control 'CalibrationForm' accessed from a thread other than the thread it was created on.
on this line:
base.Dispose(disposing);
immediately after the last calibration point. I'm using visual c# 2005 express edition on a windows xp home machine. I can run the precompiled application, and my wiimote connects fine etc. Is there a certain configuration I need to be compiling in to get this to work or any additional files I need? I haven't put very much time into researching this problem, so it may be trivial to fix, but I figured it was worth posting anyways for anyone who might be as surprised as I was when the original source did not compile. Any help would be appreciated.
nawaf
ReplyDeletecheck out wiimoteproject.com
those issues have been addressed there.
off the top of my head, the second issue is a cross thread protection from c# and there is a property you can set to disable that. it is on the forum.
the other one is addressed there as well
John:
ReplyDeleteI downloaded the C# source code from this board, and when I attempt to run the program in debug mode I get this error:
A call to PInvoke function 'WiimoteWhiteboard!WiimoteWhiteboard.Form1::mouse_event' has unbalanced the stack. This is likely because the managed PInvoke signature does not match the unmanaged target signature. Check that the calling convention and parameters of the PInvoke signature match the target unmanaged signature.
on this line:
mouse_event(MOUSEEVENTF_LEFTDOWN, 0, 0, 0, 0);
the first time I attempt to click with the ir pen when calibrating.
and if I uncheck the cursor option, and try it I get:
cross-thread operation not valid: Control 'CalibrationForm' accessed from a thread other than the thread it was created on.
on this line:
base.Dispose(disposing);
immediately after the last calibration point. I'm using visual c# 2005 express edition on a windows xp home machine. I can run the precompiled application, and my wiimote connects fine etc. Is there a certain configuration I need to be compiling in to get this to work or any additional files I need? I haven't put very much time into researching this problem, so it may be trivial to fix, but I figured it was worth posting anyways for anyone who might be as surprised as I was when the original source did not compile. Any help would be appreciated.
How could I "port" this hack to a standard USB Webcan? I know any webcam is actually IR-sensitive (you just need to remove a filter).
ReplyDeletejumpjack
ReplyDeleteCheck out motion tracking for webcams on google. there are very many solutions out there. but to convert a webcam to do the same thing, you would need to write all the processing of the brightest dots. the wiimote has all that built in so you would have to take it one step further by creating your own tracking portion before you ever got to the normal whiteboard part
www.wiimoteproject.com
Please can any one help
ReplyDeleteI downloaded the C# source code from this board, and when I attempt to run the program in debug mode I get this error:
A call to PInvoke function 'WiimoteWhiteboard!WiimoteWhiteboard.Form1::mouse_event' has unbalanced the stack. This is likely because the managed PInvoke signature does not match the unmanaged target signature. Check that the calling convention and parameters of the PInvoke signature match the target unmanaged signature.
on this line:
mouse_event(MOUSEEVENTF_LEFTDOWN, 0, 0, 0, 0);
the first time I attempt to click with the ir pen when calibrating.
and if I uncheck the cursor option, and try it I get:
cross-thread operation not valid: Control 'CalibrationForm' accessed from a thread other than the thread it was created on.
on this line:
base.Dispose(disposing);
immediately after the last calibration point. I'm using visual c# 2005 express edition on a windows xp home machine. I can run the precompiled application, and my wiimote connects fine etc. Is there a certain configuration I need to be compiling in to get this to work or any additional files I need? I haven't put very much time into researching this problem, so it may be trivial to fix, but I figured it was worth posting anyways for anyone who might be as surprised as I was when the original source did not compile. Any help would be appreciated.
Bought my IR LEDs from http://www.mouser.com/
ReplyDeleteAnd calculated the resistor values using this calculator
http://ledcalculator.net
Working great :D
Hello community, I've just got my bluetooth adapter and it's running with the BlueSoleil software. Is their a place that I can just buy an IR Pen from? As I'm not the best at DIY jobs.
ReplyDeleteRegards,
Andrew
This comment has been removed by the author.
ReplyDeleteJust got done creating my first pen with my dad. I know it's generating a IR signal as I can test that - will test the rest tomorrow.
ReplyDeletePics of the completed pen
http://galleries.keithmcd.com/gallery2/v/Projects/WiiSmartboard/
Your whiteboard works with lighters, cigarrettes, and any source of bright light.
ReplyDeleteI paint with my joint !!! Great Job! XD
Hello Mr. Lee,
ReplyDeleteI'm working with my pupils in this project of doing a Interactive whiteboard out of a wii-mote.
Great ideia, thanks for sharing with us all :-)
LPitta from Portugal
Fantastic work. I'm no geek, but had no trouble cannibalizing an IR LED from an old Tivo remote to replace the LED in a $3 pen lite. Works like a charm on my notebook LCD!
ReplyDeleteI wanted to demonstrate this at work where our meeting rooms are equipped with large screens/projectors. Just one problem: I can't reach high enough to calibrate the top corners. This had me thinking that a useful feature for the next release would be the option to calibrate to full screen (default) or only a portion of it (i.e., bottom half, or lower left quadrant, or an arbitrary height/width + 0,0 axis for placement).
Is there an aspect to how the software must work that would make this impossible? It would really help for those working in front of medium-to-large scale projections.
Wouldn't be easier to configure a bottom screen "sensor bar"?
ReplyDeleteFound Infrared LED on Ebay! Just search "infrared pen", and you get the key chain infrared LED. Not the perfect pen but works well for this project.
ReplyDeleteDear Johnny,
ReplyDeleteMay I just say this is fantastic work and it will really do amazing amounts of good for schools in countries where the economy is still developing.
Please do keep up the good work and continue to update and improve this wonderful idea as I'm sure that as word of this creeps round the internet your idea will become more and more popular and more and more widely used.
I have written about this in my ict in language education blog and will definitely be trying out this project.
Good work that man!
Seth.
Anyone have information regarding Vista compatibility? Every time I launch the whiteboard software it crashes my Vista computer...
ReplyDeletePlease email any suggestions to kimhammel@gmail.com
Has anyone tried this IR pen already made - http://www.copsplus.com/prodnum3012.php
ReplyDeleteit looks like it would work.
I'm not sure if anyone posted this comment yet, but you could use Windows onsceen keyboard to type things using the IR pen. Im pretty sure it will work but I'm not positive as of yet.
ReplyDeleteRIGHT MOUSE CLICK & WHEEL. Modify the Wiimote Whiteboard software so you can leave the pen IR LED light on all the time and just use it for mouse tracking, no clicking. Use a bluetooth mouse for left/right click and wheel. Hold the mouse in your other hand or combine the pointer and mouse into one unit. You need to cover the optical sensor on the mouse with electrical tape so it doesnt move you're pointer.
ReplyDeleteIs there any potential for damage to your LCD screen as a result of rubbing the pens all over it? I want to try this, but don't want to risk damaging my display.
ReplyDeleteI am using Vista 64 bit and I am able to connect the Wii to my computer via blue tooth. When i run the Wiiwhiteboard.exe my computer crashes and goes to blue screen. I am a teacher in Phx, AZ and really want to do this. Please help!
ReplyDeleteHow much time will the pen work? with pen cell batteries and the charger unit will also have to be in to charge the batteries ...
ReplyDeletewhat problems you see in mass manufacturing of the pens?
About right-click and parasite infra-red interferences
ReplyDeleteIt would be possible to send a radio signal with some freq. when you activate the IR LED for left-click, and another freq. for right click (2 buttons). In this way, not only do you implement the right-click, but also make it non-responsive to parasite IR sorces.
P.S. I have built the steadycam, and i'm just a paint job away from testing it ;)
you could distinguish between a right or left pointer (or the front or back of a glove) by filtering the range of infrared light reflected from the reflected surface. The software could be written to recognize the different wave length variation thus giving an "a" and "b" input. If you can build it and if it works tell me about it. my e-mail is mwhitaker@innovative-ehs.com
ReplyDeleteHi,
ReplyDeleteI want to build a LED pen too.
Can I use the following things to build one (German page)?
http://www.mercateo.com/p/139-3152868/IR_EMITTER_5MM_940NM_Typ_TSAL6400.html
http://www.mercateo.com/p/139-1400694/WIDERSTAND_15_OHM_0_1_25PPM_1206_Typ_RN73H2BTTD15R0B25.html
And which of those switches?:
http://www.mercateo.com/p/live~s.100*102-701057(2d)BP/DRUCKTASTER_R13_40A_05_SW.html
or
http://www.mercateo.com/p/live~s.100*102-701080(2d)BP/DRUCKTASTER_R13_84A_05_SW_TASTE.html
and that battery?:
http://www.mercateo.com/p/live~s.100*262-B556D44/Knopfzelle_1_55V_Si_Uhrenzellen_100mAh_V344_STCK.html
Thanks!!
I just purchased a TRENDnet TBW-101UB Bluetooth adapter and was able to get Wiimote to be recognized. I ran the wiimotewhiteboard and it comes up with "Exeption: wiimote not found in HID device list". I am running Windows XP. I cannot seem to find anything wrong as I do have things in my HID device list.
ReplyDeleteAny help would be greatly appreciated.
This comment has been removed by the author.
ReplyDeleteHey I have a Sports related question. It seems that if these remotes can be used to track movement a system could be set up to anylize and track the movement of an athlete to better understand his/her performance. Is possible to have more than one remote in different locations in order to pick up many points on an athlete?
ReplyDeletein response to leowalkman:
ReplyDeletei had the same thing happen to me, you have to make sure it appears in ur bluetooth devices page
The actual resolution of the wiimote camera is 128x96. The onboard hardware uses subpixel interpolation & tracking to give the 1024x768. See more details on the wiibrew wiki.
ReplyDeleteHello,
ReplyDeleteI have an HP Laptop running Vista 64-bit and am having alittle problem getting this to work. It detacts the wii controller via Bluetooth, I open the Calibration software, select my points....with the software always seeing an IR point......when I try to move anything, nothing happens?
This comment has been removed by the author.
ReplyDeleteThis comment has been removed by the author.
ReplyDeletei have a question, i have come to realize that for some odd reason the wiimote is "dectecting infrared motion from itself, i'm able to move, "but very limited."
ReplyDeletethe wiimote as mouse after calibration, since the wiimote has an ir all in itself, is it possible to use a SECOND wiimote as the pen in itself, thanks if you can answer!!!
This comment has been removed by the author.
ReplyDeleteThis comment has been removed by the author.
ReplyDeleteHi Lee!
ReplyDeleteGreat Job. I was impressed by seeing your whiteboard project.And try to do the same with different hardware.
I have some device apart from wii mote which detects IR or light source only. I can connect that device through USB and read detected light source as data. I am trying to connect my USB HID device by changing VID and PID with your software. Its not working & shows that device cannot found.
When i start debugging ur wiimote project code, at one point i realize program flow and it is not going inside this condition.
“if(HIDImports.HidD_GetAttributes(mHandle.DangerousGetHandle(), ref attrib))”
Could you please help me in sorting out the mentioned issue.
Advance thanks for your help!
Regards,
Mukunthan Kandasamy
Hi Lee!
ReplyDeleteGreat Job. I was impressed by seeing your whiteboard project.And try to do the same with different hardware.
I have some device apart from wii mote which detects IR or light source only. I can connect that device through USB and read detected light source as data. I am trying to connect my USB HID device by changing VID and PID with your software. Its not working & shows that device cannot found.
When i start debugging ur wiimote project code, at one point i realize program flow and it is not going inside this condition.
“if(HIDImports.HidD_GetAttributes(mHandle.DangerousGetHandle(), ref attrib))”
Could you please help me in sorting out the mentioned issue.
Advance thanks for your help!
Regards,
Mukunthan Kandasamy
I'm in a classroom. My projector projects onto a screen beyond my reach, with my whiteboard below it. Will this still work? I write on the whiteboard and it projects up on the screen? Sort of like a giant tablet.
ReplyDeleteOr do I have to work where the project is actually projecting?
I think it would be very hard to make it work if you weren't working on the same surface as the one you were projecting to. But I don't see why it would be impossible.
ReplyDeleteOkay,
ReplyDeleteI ran the calibration fine but can't get any other app to do anything. I cant drag or move a window, etc. Any ideas?
Hi, I am using the wiimote whiteboard for graphic design. The problem i face is that the mouse cursor does not move with the pen when the IR LED is not on (of course). I wonder since the mouse works when the whiteboard program is running, can you remove the mouse depression command when the IR LED is lit? So that the LED is on all the time and the position of the LED yields the position of the cursor. Then I can hack a mouse to remove the right and left click buttons, connect them to the pen with two new momentary switches. That way the cursor moves around with the pen without clicking on anything. When i push down on one of the switches connected to the mouse, it sends the mouse depression command to the PC.
ReplyDeleteHello, after connecting the remote via blue tooth and downloading and extracting the software, it blocked my usage of the program saying: "Exception: wiimote not found in HID device list" . Any help? I'm using windows XP.Thanks -- Joshua
ReplyDeleteHi,
ReplyDeleteThe system needs to recognize the new device. Most probably, this has not happened.
When you connect the wiimote to the system, Windows should recognize it as some kind of HID (Human Interface DeviceÜ) - I think its a joystick that comes up, and install the drivers for it.
If this step does not happen, then the Wiimote is not really connected to your system and thus the software will not be able to find it either.
I think this is the reason for your error message.
You should try BoonJin's software.
ReplyDeletehi i want to try and use this on my computer screen like in one the videos with the laptop..but i have a a CRT monitor and in the vid it said for any "liquid crystal display"... does this work on CRT monitors?
ReplyDeleteI havent tried this yet, but i am trying to find a bluetooth adapter, then go make the ir pens, but i think the calibration scheme should be changed
ReplyDeletei would expect that the calibration starts at the top left, then goes to bottom left, top right, bottom right, as this would be more natural, and might be easy to implement
Would more points of calibration make this more accurate, less jagged or something, because the smartbard had 9 points of calibration. Maybe you could add a calibration point, right in the center. The pressure tip may be usefull, but you will scratch up your led, and it might not work as well. you could wrap in the a cloth with lots of wholes, and make the led really powerful, as the cloth will limit the brightness, and this would stop the relfection prob some ppl are experencing
By the way, i love this idea, i think another guy made this with 2 wii remotes, so if you cover one, the other one picks up, but could you implement a shutdown, as you click a button, the remote turns off, and then you could press the button a, and it would reconect, and work
ReplyDeletekeep up you good work
One thing that would be truly useful would be a modification that hooked the Wiimote directly to the computer via a USB connection (bypassing the Bluetooth).
ReplyDeleteThis would be for:
1. Powering the Wiimote via USB instead of batteries
2. Eliminating the need to start up a Bluetooth connection
This would be advantageous to folks who would prefer to mount the whiteboard Wiimote up high (ie. ceiling mount). It would also be excellant for folks doing Wiimote-based headtracking. Instead of mounting a Wiimote on the top edge of a display, It could be mounted directly over the user, thereby minimizing the chances of the head blocking a view of the IR LEDS. Great work and promotion going on here. Thanks!!
Mr. Lee, Thank you. I put the smartboard in our game room and my daughter and her friends love it!!
ReplyDeleteThanks again.
This comment has been removed by the author.
ReplyDeleteHas anyone tried a green laser pointer?
ReplyDeleteGreen laser pointers use an infrared laser with a frequency doubler to get to green, and then add a filter to clean out the IR.
I would expect that if you knocked out the filter you would have a green cursor mixed with infrared.
I have installed everything and followed all the steps, however everytime i try the ir pen on my lcd screen the wii remote goes crazy. I really don't know why it seems to detect 2 or 3 signals. I use only one ir pen and the pointer goes crazy on the screen.
ReplyDeletePlease help!!!
I'm trying to get the wiimote to sync with a Jabra A320a. Has anyone had success with this? Do I have to buy BlueSoleil to make it work?
ReplyDeleteHow much advanced programming (and/or hardware) are we talking about if we used your whiteboard project to emulate Arcstream Living Image floor projection system? For example, people walking across the illuminated floor, creating "water ripples" or "chasing fish away".
ReplyDeleteI imagine it's more involved with precise IR tracking system? Along with some fancy coding for FX?
John,
ReplyDeleteWhat is the mathematics behind the calibration?
I coudln't find anything useful on google... I just considered the vectors made by the theorical coordinates of the calibration points and the actual coordinates read by the wiimote, then compute the polar coordinates of those vectors and compute 2 maps, one for r and one for theta, using the bilinear interpolation algorithm. It works ok when the deformation is small, but very bad whith big deformation.
Do you have any pointers to some of the theory and math behind your calib?
Thanks.
JD,
ReplyDeleteYou might get better results in asking this on WiimoteProject There are a couple of people that have made their own apps that would be able to help you better.
what is the program called that you use to link the remote to your computer??
ReplyDeletethanks
Take a look at this.
ReplyDeleteWiimote Connection Guide
I am planning on aiming the Wii camera at my coffee table from directly above. It will take a little trial and area to do the initial calibration as I will not be able to see the calibration points but once done will be laughing. Reason being I am going to use hand gestures over my coffee table to control media centre PC. Instead of a pen I am making in IR finger attachment with a tilt activated switch. eg. To change channel I will move my hand over the coffee table, guide the curser to the channel button and title my finger.
ReplyDelete@john
ReplyDeletethats a cool idea
but it might just be easier to create a printout
and you would have to make custom code to reconize gestures
or make custom code so that spacific areas of you paper are like hit spots
or a custom interface
Hi johnny
ReplyDeletedo you think the Wii Motionplus will improve the tracking accuracy ? I cannot use it with Gran Slam Tennis anyways :)
These projects are awesome. I recreated the whiteboard and all applications I tried work fine for now.
ReplyDeleteOnly the programming language Scratch doesn't work correct. When I want to drag and drop a block I only have a right click event. All other apps use the normal left click. Why does that happen? How can I solve the problem?
Hello,
ReplyDeleteI am Vijay,
I downloaded the code for Interactive white board. When I tried to make it run, I am getting a problem with the fourth calibration point. The exception is
("Cross-thread operation not valid: Control 'CalibrationForm' accessed from a thread other than the thread it was created on".)
Guys please help me on this exception.
If you have any solution please send me a mail to sit.raju@gmail.com
Hello!
ReplyDeleteIs this possible to integrate the Interactive white board software and wiimote presenter into single using two wiimotes.
If possible help me how to solve this?
Thanks & Regards,
Karumanchi
Wow. I remember you heptic pen. There should be a way to adapt it to the Wiimote Whiteboard. That could then use pressure sensitivity, so you could implement it into doing things like the pressure slider you posted (from that other team) and stuff like that.
ReplyDeleteThis could easily make a great DIY package. I mean, you could sell, even in the spirit of just taking the technology everywhere, packages for doing this project. Something in the way of self calibrating projector image would be great too.
Concerning the right click, what about the approach the touchscreen phones have? Just maintaining the pen in one spot for a while.
This would be great for schools that need the tech but don't have the cash.
Does anyone know of a green IR laser that works for the wiimote whiteboard?
ReplyDeleteed hardy clothes
ReplyDeleteWholesale Handbags
babolat aeropro drive
Levi jeans
Diesel Jeans
Levis Jeans
puma basket
Lacoste polo shirts
nike max shoes
Hello
ReplyDeleteI tell you that your project seems great, I feel the responsibility to inform you that your project was abducted by some persons they wish to present as their own when they are not even credit you as the person who developed the link to review the information is here http://itsanjuan.edu.mx/index.php?option=com_content&view=article&id=107:alumnos-que-obtuvieron-el-1er-lugar-en-el-xxiv-evento-nacional-de-creatividad-en-su-fase-regional-con-el-proyecto-pantalla-multiproposito&catid=9:infogralinstitucional
Hello
ReplyDeleteI tell you that your project seems great, I feel the responsibility to inform you that your project was abducted by some persons they wish to present as their own when they are not even credit you as the person who developed the link to review the information is http://itsanjuan.edu.mx
Hi
ReplyDeletewe have developed our own hardware for white board and its working almost fine. Our Team doing final fine tuning in own software. Please contact us if anybody interested in demo and business for whiteboard hardware and software.
Mukunthan Kandasamy
+919922933855 (India)
I rebuilt the project in MS Visual Studio 2008 on Windows 7 64 bit. At first the cursor control didn't work (mouse didn't move). After I changed the platform to x86 the mouse control worked fine.
ReplyDeleteJohnny you rule!
levitra efectos secundarios
ReplyDeleteohne rezept levitra
venta de cialis
prix cialis pharmacie
apotheke levitra
controindicazioni levitra
ohne rezept levitra
viagra senza ricetta
levitra rezeptfrei bestellen
la cialis
IR filter in one with a normal light filter. This is how it's usually done with DIY multi-touch surfaces.
ReplyDeleteDissertations | Essays | Theses
Thanks for sharing.Great post, i really appreciate it.
ReplyDeleteResearch Papers | Term Papers
levitra en ligne
ReplyDeleteohne rezept cialis kaufen
viagra rezeptfrei
kamagra vente en pharmacie
venta de viagra soft sin receta
viagra soft kaufen
plavix bestellen
viagra bestellen
just an idea: if the wii remote is colour-sensitive, why not to simulate right-click by different colour LED? You are loosing one tracking point, but getting real mouse behaviour...
ReplyDeleteFeatured : Buy Cialis Online at The Leading Generic Pharmacy | Buy Cialis Pills
ReplyDeleteBuy Cialis Online at the leading discount generic pharmacy. Cheap generic drugs for erectile dysfunction treatment.
vermox rezeptfrei bestellen
ReplyDeletetamiflu ohne rezept kaufen
lovegra kaufen
lovegra kaufen ohne rezept
propecia rezeptfrei bestellen
levitra ohne rezept
tamiflu rezeptfrei kaufen
kamagra kaufen
accutane bestellen ohne rezept
viagra soft rezeptfrei
zyloprim kaufen
strattera rezeptfrei